LEVEL YAPIWHAT IS NATURAL SHIELD?
It is a water, fire, water and sound insulation material,
Granularly produced with new generation high technology,
With inorganic binding (containing no harmful substances for health),
Containing crystallized glass,
This is produced by blowing recyclable glasses at high temperatures and trapping air sacs in them.
LEVEL YAPIWHY NATURAL SHIELD?
NATURAL SHIELD
HEAT INSULATION
FIRE INSULATION 
SOUND INSULATION
WATER INSULATION
HEAT INSULATION
The Natural Shield insulation solution provides continuous insulation, not allowing heat bridges between the interior and the exterior, with heat savings up to 55%.
- Cold weather remains outside in winter and hot weather inside.
- Hot weather remains outside in summer and cool weather inside
- Its value on the lame is 0,039.
FIRE INSULATION
Natural Shield fire is fully fire-resistant. It is class A in terms of flammability. Other products on the market are flammable and of class B products.
-
Not flammable until 1100 ° C.
- It is in class A1 fire resistant material according to DIN 4102.
- No sultry smoke, heat, toxic gas during the fire.
SOUND INSULATION
Sound insulation is much more than other materials used for cladding.
- Porous structure does not reflect sound, it helps to improve comfort with sound absorption feature in buildings.
- Provides sound insulation up to 42 decibels.
WATER INSULATION
Natural Shield does not contain water and moisture due to polymers and other water repellent natural components in its structure.
-
Air permeability is maintained when the special structure pushes water, preventing humidity and mold formation.
HEAT INSULATION SAVING
~ %55
NOT FLAMMABLE
UNTIL
1100°C
FIRE RESISTANT MATERIALS
A1 CLASS
PROVIDES SOUND INSULATION UP TO
42 DECIBELS
ITS VALUE ON THE
LAME IS
0,039
OTHER IMPORTANT FEATURES OF NATURAL SHIELD
No sultry smoke, heat, toxic gas during the fire.
Does not contain radioactive and carcinogenic substances.
It is resistant to impact and pressure; it does not allow cracks and damages.
Compressive strength: 3,3 N / mm2, Bending strength: 1,8 N / mm2, Bond strength: 0,94 N / mm2
Thanks to its lightness it reduces the load on the building. Dry unit density: 310 – 325 kg/m³,
Damage repair is done simply and cost-effectively with application to the damaged zone only.
Compared to conventional plastering and other methods of cladding, the burden placed on the building is much less, which reduces the impact of the earthquake considerably.
LEVEL YAPI NATURAL SHIELD & OTHER INSULATION METHODS
NATURAL SHIELD
It is applied directly to materials such as brick, pumice, aerated concrete, gross concrete, iron, precast concrete panel, ceramics and glass with its superior adhesion properties. No need for anchor holes. Finish with single application.
Save %50 time. Reduce labor costs to a minimum. Easier to apply than plaster. Can be applied by hand or with a plaster dispenser.
Loads much less on the building.
Does not allow heat bridge formation.
NATURAL SHIELD
LEVEL YAPI FIELDS OF APPLICATION
External Facade
Exterior heat, fire, water and sound insulation.
Having high adhesion strength.
It is easily applied to surfaces such as concrete, pumice, brick, aerated concrete, ceramic, glass and so on.
Not affected by environmental factors.
Ground
Provides heat, fire and sound insulation between floorings.
It is applied directly on the floor and the conventional screed is applied at the desired thickness.
Ideal for underground heating systems and provides high energy savings.
Internal Facade
Alternative for gypsum plaster
With Natural Shield Interior Wall Plate, besides a smooth surface, heat, fire and sound insulation are also obtained.
Since it breathes thanks to its special structure, it prevents the moisture and mold as a result.
LEVEL YAPI TECHNICAL SPECIFICATIONS
NATURAL SHIELD
Technical Specifications of Natural Shield
Pressure Resistance: 3,3 N/mm2
Bending Strength: 1,8 N/mm2
Tie Strength: 0,94 N/mm2
Water Vapor Diffusion Resistance Factor (μ): 5,5 ( TS EN 1015-19 )
Dry unit density: 310 – 325 kg/m3 ( TS EN 1015-10 )
Load per m2 in practice: 6,0-6,7 kg/m2 (at the thickness of 2cm)
Fire Class: A1 ( TS EN 13501-1 )
Heat Conductivity: T1 ( TS EN 1745 )
Water Absorption Rate: W1 ( TS EN 1015-18 )
Bonding to bottom plate: 0,90 Mpa
Appearance: White
Mixture Rate: 11 kg powder / 7-8 lt water
Application Temperature: +5˚ and above
Packaged Storage Time: 2 Years
Applicable THICKNESS: 4 – 150 mm
Note: All values were delivered at +22 degrees and 55% relative humidity.
Water Isolation and Lightness
Natural Shield Insulation plaster at the thickness of 10 cm is placed in the middle of the aquarium and divided into two. Water is placed on the top of the aquarium but the bottom is left empty. Air is pumped through the lower chamber. As you can see in the pictures, no water will pass through to the bottom while air passes to the top. Thanks to its lightweight components and water repellent properties, the Natural Shield does not sink when it is thrown into the water and remains on the water.
Bonding and Burning Experiment
A specific point of the Natural Shield coated surface is heated to 700 ° C. It is observed that the surface temperature is about 30 ° C when looking at the temperature of this surface using a point thermal machine. This shows that the material prevents the heat from getting distributed to the other side.
Natural Shield General Features
Heat Insulation
Natural Shield products provide continuous insulation, allowing no heat bridges between the interior and the exterior and saving up to 55% heat.
Water Insulation
Natural Shield products are not subject to penetration of water and moisture due to their polymers and other water repellent natural components. Air permeability continues while its special structure pushes water out.
Sound Insulation
Sound insulation is much more than other materials used for cladding. Porous structure does not reflect sound, it helps to improve comfort with sound absorption feature in buildings.
Earthquake Resistance
Natural Shield is 5-6 times more lightweight than other cladding methods. In this view, building load is reduced and is much less affected by earthquakes.
Easy to Paint
Natural Shield products become ready-to-use exterior wall paint between 16 and 48 hours when ambient temperature is appropriate.
Prevents Moisture and Mold Formation
It forms air cutters on the surface due to its material structure. In this way, the air that is heavy and humid can easily be thrown out. This ensures that the building gets air.
Natural Shield is
100% Environmentally Friendly
- Natural Shield does not contain any chemicals in its structure. On the contrary, Natural Shield, which is made entirely of natural materials, is also environmentally friendly as well as having UV resistance.
